1998 Custom Built Constructions Marines, La Trinite sur mer, Brittany Aluminum Cutter Cruiser
Length: 7.87 m
Beam: 2.77 m
Berths: 3
Fuel: Diesel
1998 Custom Built Constructions Marines, La Trinite sur mer, Brittany Aluminum Cutter Cruiser boat for sale
Broker Remarks
Sandy is a truly individual 8m aluminium cutter cruiser, built in Brittany in 1998 to a John Sadler design. Constructed with an unsinkable foam-filled hull and twin swing keels, she offers an unusual combination of shallow-water capability, sailing performance and practical cruising. She has been exceptionally well maintained and has benefited from an impressive programme of upgrades, including renewed standing and running rigging, a new mainsail, hull repaint, upgraded electrics and navigation equipment, new batteries and wiring, gearbox service, new prop shaft and numerous engine works. With comfortable accommodation for three, a well-appointed interior, beaching legs and an extensive sail inventory including a cruising asymmetric spinnaker and storm trysail, Sandy is a fascinating and capable little cruiser, ready for her next adventure.
Accommodation
Accommodation for up to 3 persons
Main cabin with 2 single berths
Additional quarter berth
Comfortable interior with good headroom
High-quality wooden lockers and storage
Galley positioned within the main cabin
Dedicated navigation table
Large sliding skylight providing excellent natural light
Small enclosed WC compartment Chemical toilet
Galley sink Single-ring alcohol cooker
Cutlery and crockery included
Heavy-duty interior soft furnishings
Interior cushions reupholstered in 2024
70-litre aluminium freshwater tank
Shore power connection
Mechanical and Rigging
Construction
1998
Aluminum, Cutter Cruiser
Aluminium Hull with twin swing keels
Hull repainted in 2023
Mechanical
Yanmar 1GM10 - 9hp
Diesel Engine
Raw Water Cooled
Stainless Steel 70 litres tank Stbd Midships
Stainless steel shaft, fitted with a Volvo inboard seal and a water lubricated stern seal
Gearbox serviced - 2024
New prop shaft - 2024
Fixed prop - 2024
Engine serviced - 2026
New exhaust valve, new stainless steel exhaust elbow, cylinder head machined - 2026
Electrical
2 X batteries - 2025
Solar Panel
Shore power connection Victron galvanic isolator
Inventory
Sails & Rigging
Mainsail - new in 2023
Spare mainsai
Furling jib
Storm trysail
Crossing asymmetric spinnaker
Standing rigging renewed in 2022
Running rigging renewed in 2022
Plastimo roller furler for jib installed in 2025
Bowsprit rerigged with wires from GS Products; new dyneema halyard for yankee - 2024
Harken winches
Aluminium custom made mast by Technique Gremeni
Fully orientable bowsprit
Deck equipment
Tiller steering
Fully supported rudder
Harken manual winches
3 x anchors
3 x sets of anchor chain and rope
Fenders
Beaching legs
Seadek foredeck covering done - 2022
Full winter cover - 2023
Rebuilt sliding coach roof with Iroko rails - 2026
Navigation Equipment
Raymarine Axiom 7 inch plotter - 2022
Cobra DSC VHF - 2022
Depth sounder, log / speed unit - 2022
Garmin GPS 128 plotter
Autopilot
Disclaimer
Network Yacht Brokers normally acts as brokers for the vendor who unless otherwise stated is not selling in the course of a business. Whilst every care has been taken in the preparation of these particulars the correctness is not guaranteed and they are intended as a guide only and do not constitute a part of any contract. A prospective buyer is strongly advised to check these particulars and where appropriate and at his own expense to employ a qualified marine surveyor to carry out a survey and/or to have an engine trial conducted which if conducted by us shall not imply any liability on our part.
General note on safety equipment: Any safety equipment such as liferaft, fire extinguishers and flares etc., are usually personal to the current owner(s) and if being left on board as part of the sale of a used vessel, may require routine servicing, replacement, or changing to meet a new owner’s specific needs.
